cylinder head

In the thermal fatigue test of cylinder head, the shaped laser beam is chosen as the heating source to simulate the real fatigue.

气缸盖激光热负荷试验采用整形激光束作为热源模拟实际工况下气缸盖承受的热负荷。

The conclusions are of benefit to the improvement of the diesel engine with integrated cylinder head.

得出的结论有益于对整体式气缸盖柴油机的改进设计.

The operation performance of a spark ignition natural gas engine with two cylinders, including dynamometer card in cylinders, intake pressure liquid, air fuel ratio, temperature field of cylinder head and piston, and emission, is tested.

对一台火花点火式两缸天然气发动机进行了缸内示功图、进气压力波、空燃比、缸盖及活塞温度场和排放等项目的测试。

Clean the exhaust manifold and cylinder head mating surfaces.

清洁排气歧管和汽缸头配合面.

Research on Fatigue Test of Solid Cylinder Head

整体汽缸盖疲劳试验研究

A process of cylinder-head structure optimum is described in this paper.

介绍了气缸盖的结构优化过程.

Test of flow distribution was performed on the cylinder head of typical Turbocharged diesel engine using flow display method and 2D flow field of cooling water in the cylinder head was obtained.

采用流动显形法对典型增压柴油机气缸盖进行水流分布试验，得到冷却水在缸盖中的二维流场。

Place the engine cylinder head over the dowels.

将引擎汽缸头放在销上.

A new lateral casting process was introduced to produce YC 6 M cylinder head.

介绍了生产YC6M缸盖的侧浇铸造新工艺.

The basic casting method-design principle of cylinder head was introduced.

介绍灰铸铁缸盖铸造工艺的基本设计原则.

The cylinder head is heavily finned for strength.

汽缸头附有许多突片以增加强度.

This is achieved by using cylinder head gasket.

这通过使用气缸盖衬垫实现.

Simulated Experimental Study on Extension Characteristics of Thermal Fatigue Crack of Cylinder Head

缸盖热疲劳裂纹扩展特点的模拟试验分析

The cast production technology and its control means of Cumins 6 BT cylinder head production are described.

叙述了康明斯6BT气缸盖铸造生产工艺及控制手段.

The powder cylinder head good case of impurities. 3.

夺目把粉缸关好,以防杂质出去.

Multi-Model Technology and Its Application in Cylinder Head Development Process

多模型技术及其在发动机缸盖开发过程中的应用

An Investigation into Influences of Exhaust port Heat Insulating Methods on Total Temperature Field of Cylinder Head

排气道隔热方式对气缸盖整体温度场影响的研究

Numerical simulation for the low pressure of an engine cylinder head

发动机缸盖低压铸造数值仿真技术

The features of cylinder block and cylinder head core assembly vertical casting process are introduced.

介绍了缸体、缸盖组芯立浇工艺的特点.

Experimental Investigation on the Water Coolant Flow Field of Engine Cylinder Head

发动机缸头冷却水流场试验研究

This paper studied the trouble characteristic extraction and identification methods based on snatch AR analysis, wavelet many resolutions analysis and wavelet packet analysis, and analyzed vibration signal characteristic extraction method for diesel engine cylinder head.

研究了基于短时AR分析、小波多分辨率分析和小波包分析的故障特征提取和识别方法，分析了柴油机气缸盖振动信号特征提取方法。

Application of Digital Factory in Process Planning for Engine Cylinder Head

数字化工厂技术在发动机缸盖工艺规划中的应用

Though the temperature measurement test on cylinder head, the thermal conditions are analyzed and the results are obtained for comparison with simulation.

进行温度场测量试验，分析气缸盖热负荷情况并为模拟结果提供对比数据。

Remove control cables from cylinder head cover clip.

从汽缸头盖扣夹上移去控制拉索.

The main defect of type YC 4112 Q cylinder head is blowhole.

气孔为YC4112Q气缸盖的主要缺陷.

Topology Optimization Application on Low Noise Design of Cylinder Head Cover

拓扑优化技术在缸盖罩低噪声设计中的应用

Study on the Load-bearing Mechanism of Some Key Function Structures of Cylinder Head

气缸盖中一些关键功能结构的承载机理研究

The most common cylinder head types are the hemi, wedge, and semi-hemi.

最常见的气缸盖类型是半球形, 楔形和准半球形.

The cylinder head is attached to the block with high-tensile steel studs.

气缸盖与气缸体用高强度的钢螺栓缚连结.

Study on vibration signal characteristic extraction method for diesel engine cylinder head

柴油机气缸盖振动信号特征提取方法的研究